BoYue Steel China Co.,Ltd
BoYue&Tianda Oil Pipe Co., Ltd
BoYue Industry (ShangHai) Co., Ltd
BoYue & BaoSteel Pipeline Equipment Co.,Ltd
Payment & Shipping Terms:
|Name:||SO Pipe Flanges||Material:||Alloy Steel|
|Size:||2"-12"||Pressure:||150#, 300#, 400#, 600#, 900#, 1500#, 2500#|
|Manufacturing Process:||Push,Press,Forge,Cast,etc.||Standard:||ANSI:ANSI B16.5, ANSI B16.47, MSS SP44, ANSI B16.36, ANSI B16.48,DIN:DIN2527, DIN2566, DIN2573, DIN2|
|Delivery Time:||30 Work Days||Flange Type:||WELD NECK FLANGE , LAP JOINT FLANGE, BLIND FLANGE, SLIP ON FLANGE, THREAD FLANGE, SOCKET WELD FLANGE ORIGICE FLANGE , SPECTTACLE FLANGE, OVERLAY CLADDING|
flange slip on type,
slip on forged steel flange
ASME Slip On Pipe Flanges Alloy Materail ASTM A182 F11, F22, F5, F9, F91, F92 , Size1/2'-24'
Slip-on Flanges have a lower initial cost than welding neck flanges because they require less accuracy in cutting pipe to length, and they provide a greater ease of alignment in assembly. However, their calculated strength under internal pressure is approximately 2/3's the strength of welding neck flanges, and their life under fatigue is 1/3 shorter. Slip-on Flanges are limited to 1/2" to 2½" sizes in 1500lbs standard.
Threaded Flanges are used for special applications. They can be assembled without welding and can be used in extremely high pressure services--at or near atmospheric pressure--where alloy steel is essential for strength. Threaded flanges are not suited for conditions involving temperature or bending stresses, or under cyclic conditions where leakage through the threads may occur.
Weld Neck Flanges
Weld Neck Flanges have a long tapered hub and gradual transition of thickness in the region of the butt weld joining them to the pipe. The tapered hub provides important reinforcement to the flange and resistance to dishing. This type of flange is preferred for severe service conditions resulting from high pressure, sub-zero or high temperatures.
Blind Flanges are used to blank off the ends of piping, valves and pressure vessel openings. Blind Flanges can handle high stress from internal pressure and bolt loading since the maximum stresses in the blind flange are bending stresses at the center.
Socket Weld Flanges
Socket Weld Flanges were developed for use on small size high pressure piping. With an internal weld, socket weld flanges are stronger and have greater fatigue strength than double welding a slip-on flange. Smooth bore conditions can be easily attained by grinding the internal weld. This flange is commonly used in chemical process piping.
Lap Joint Flanges
Lap Joint Flanges are used with lap joint stubs. Lap joint flanges are commonly used in carbon or low alloy steel piping systems that need to be frequently dismantled for inspection and cleaning. They should not be used at any points where severe bending stresses occur.
We offer high quality DIN flanges that conform to the standard specifications of DIN
Designs of flanges:
A wide variety of flange designs are available. They are available in various shapes and sizes. Some of the popular designs are as follows:
Custom shapes and sizes are also manufactured by numerous manufacturers. Various pipe flanges include machining details such as gasket surfaces, facing details, non-standard drilling, bevel and radius edges, o-ring grooves and raised or recessed faces. Some typical designs on flanges faces are shown below.
Advantages of slip on flanges:
Low cost installation
Less time needed to spent on ensuring the accuracy of the cut pipe
they are somewhat easier to align
the slip-on flanges have low hub because the pipe slips into the flange before welding
the flange is welded both inside and outside to provide sufficient strength
they prevent leakage
Key Features of Slip-On Flanges :
Some important features are as follows:
One size fits all pipe schedules.
Fabricators can more easily cut pipe to length for slip-on flanges.
The smaller thickness of this flange allows for easier alignment of bolting holes.
They are generally not preferred for high pressure temperature environments.
Size : 1/8" NB TO 48"NB.
Class : 150#, 300#,400 #,600#,900#, 1500# & 2500 #.
Stainless Steel Slip on Flanges: ASTM A 182, A 240
Grade : F 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H,904L, Duplex stainless steel UNS S31803, 2205, Super Duplex stainless steel UNS S32750
Carbon Steel Slip on Flanges : ASTM A 105, ASTM A 181
Alloy Steel Slip on Flanges: ASTM A 182, GR F1, F11, F22, F5, F9, F91
How to measure slip-on flanges?
Take the measurements of:
BOYUE STEEL deal with Austenitic Stainless Steel, Nickel Alloy Steel(Hastelloy , Monel, Inconel, Incoloy ) seamless and welded pipe and tube already more than 25 years, every year sell more than 80000 tons of steel pipe and tube. Our client already cover more than 45 countries, Like Italy, UK, Gernmany, USA, Canada, Chile, Colombia, Saudi Arabia, Russia, Korea, Singapore, Austrial, Poland, France , ....And our group branch company and factory have been already approved by :ABS, DNV, GL, BV, PED 97/23/EC, AD2000-WO, GOST9941-81, CCS, TS, CNNC, ISO9001-2008, ISO 14001-2004.
|Place of Origin||China||Brand Name||BOYUE|
|Standard||ASME B16.5||Type||SO Flange|
|ModelNumber||Duplex Stainless Steel||Thickness||Sch40s,Sch80s,sch160|
|Packing||Ply-Wood Cases||Payment||30%TT+70% Balance|
Supply Ability:30000Pieces / per Month
Packaging & Delivery
Packaging Details:Generally ply wooden case or following customer's requirement.
|Price:||Depending on quantity|
|Minimum Order Quantity||1 PCS|
|Payment Terms:||T/T or Western Union or LC|
|Supply Ability:||3,0000pcs per month|
|Delivery Time:||10-100 days depending on quantity|
|Packaging Details:||PLY-WOODEN CASE OR PALLET|
Why Choose Us
1.One-Stop Service,One Single Source.
3.Best quality,competitive price
6.Professional sales and technical team .
Q1: Are you a factory or a trade company?
A1: We are a professional manufacturer for designing and producing of Large-size products.(View Mor)
Q2: Do you make customized products or finished parts?
A2: All parts are custom made only, and in stock, we can produce based on your drawings.
Q3: Will my drawing be safe after you get it?
A3: Yes, we will not release your design to third party unless with your permission.
Q4: What is the MOQ?
A4: Small order is acceptable, but the more, the cheaper.
Q5: How about the samples?
A5: We are happy to make prototype part or sample for clients to ensure quality standard, but it’s charged according to your drawing.