BoYue Steel China Co.,Ltd
BoYue&Tianda Oil Pipe Co., Ltd
BoYue Industry (ShangHai) Co., Ltd
BoYue & BaoSteel Pipeline Equipment Co.,Ltd
Payment & Shipping Terms:
|Product Name:||Alloy Steel Pipe||Type:||Seamless Or Welded|
|Standard:||ASTM A335 P5||Prodcut:||Steel Pipe Tube|
SCH5 alloy steel pipe,
ASTM A335 P5 alloy steel pipe
Alloy Steel Pipe ASTM A335 P5 Durable Seamless Heavy Duty High Toughnesss
Orders for material under this specification should include the following, as required, to describe the desired material adequately:
1 Quantity (feet, centimetres, or number of lengths),
2 Name of material (seamless alloy steel pipe),
4 Manufacture (hot-finished or cold-drawn),
5 Size (NPS or outside diameter and schedule number or average wall thickness),
6 Length (specific or random),
7 End finish (Ends Section of Specification A 999/A 999M),
8 Optional requirements (Section 8, 11 and 12 of specification ASTM A335. See the Sections on Hydrostatic Test Requirements and Permissible Variation in Weight for Seamless Pipe in Specification A 999/A 999M),
9 Test report required (Certification Section of Specification AA 999/A 999M),
10 Specification designation, and
11 Special requirements or any supplementary requirements selected, or both.
Materials and Manufacture
1 Pipe may be either hot finished or cold drawn with the finishing treatment as required in 3.
2 Grade P12—The steel shall be made by coarse grain melting practice. Specific limits, if any, on grain size or deoxidation practice shall be a matter of agreement between the manufacturer and purchaser.
3 Heat Treatment:
3.1 All pipe of grades except P5, P91, P92, shall be reheated and furnished in the full-annealed, isothermal annealed, or normalized and tempered condition. If furnished in the normalized and tempered condition, the minimum tempering temperature for Grades P5, P5b, P9, P21, and P22 shall be 1250°F [675°C], the minimum tempering temperature for Grades P1, P2, P11, P12, and P 15 shall be 1200°F [650°C].
NOTE—It is recommended that the temperature for tempering should be at least 100°F [50°C] above the intended service temperature; consequently, the purchaser should advise the manufacturer if the service temperature is to be over 1100°F [600°C].
3.2 Pipe of Grades P12, either hot finished or cold drawn, may be given a final heat treatment at 1200°F [650°C] to 1300°F [705°C] instead of heat treatments specified in 3.1.
3.3 All pipe of Grades P5c shall be given a final heat treatment in the range from 1325°F [715°C] to 1375°F [745°C].
NOTE—Certain of the ferritic steels covered by this specification will harden if cooled rapidly from above their critical temperature. Some will air harden, that is, become hardened to an undesirable degree when cooled in air from high temperatures. Therefore, operations involving heating such steels above their critical temperatures, such as welding, flanging, and hot bending, should be followed by suitable heat treatment.
3.4 Grade T92 shall be normalized at 1900°F [1040°C] minimum and tempered at 1350°F [730°C] minimum as a final heat treatment.
5.4 Except when Supplementary Requirement S7 is specified by the purchaser, Grade P91 shall be normalized at 1900°F [1040°C] minimum, and tempered at 1350°F [730°C] minimum as a final heat treatment. Alternatively, liquid quenching and tempering is allowed for thicknesses above 3 in. when mutually agreed upon between the manufacturer and the purchaser. In this case the pipe shall be quenched from 1900°F [1040°C] minimum and tempered at 1350°F [730°C] minimum as final heat treatment.
1 When selected by the manufacturer or when specified in the order, as an alternative to the hydrostatic test, or when specified in the purchase order in addition to the hydrostatic test, each pipe shall be examined by a nondestructive examination method in accordance with Practice E 213, Practice E 309 or Practice E 570. The range of pipe sizes that may be examined by each method shall be subject to the limitations in the scope of the respective practices.
2 The following information is for the benefit of the user of this specification:
2.1 The reference standards defined in 12.8 are convenient standards for standardization of nondestructive examination equipment. The dimensions of these standards should not be construed as the minimum size imperfection detectable by such equipment.
2.2 Ultrasonic examination can be performed to detect both longitudinally and transversely oriented discontinuities. It should be recognized that different techniques should be employed to detect differently oriented imperfections. The examination may not detect short, deep imperfections.
2.3 The eddy current examination referenced in this specification has the capability to detect significant discontinuities, especially of the short abrupt type.
2.4 The flux leakage examination referred to in this specification is capable of detecting the presence and location of significant longitudinally or transversely oriented discontinuities. It should be recognized that different techniques should be employed to detect differently oriented imperfections.
2.5 The hydrostatic test of Section 11 has the capability to find imperfections of a size that permit the test fluid to leak through the pipe wall so that it may be either visually seen or detected by a loss of fluid pressure. This test may not detect very tight, through-wall imperfections, or imperfections that extend into the wall without complete penetration.
2.6 A purchaser interested in ascertaining the nature (type, size, location, and orientation) of discontinuities that can be detected in the specific application of these examinations should discuss this with the manufacturer of the tubular products.
3 Time of Examination—Nondestructive examination for specification acceptance shall be performed after all mechanical processing, heat treatments and straightening operations. This requirement does not preclude additional testing at earlier stages in the processing.
4 Surface Conditions:
4.1 All surfaces shall be clean and free of scale, dirt, grease, paint, or other foreign material that could interfere with interpretation of test results. The methods used for cleaning and preparing the surfaces for examination shall not be detrimental to the base metal or the surface finish.
4.2 Excessive surface roughness or deep scratches can produce signals that interfere with the test
Mechanical tests required
Transverse or longitudinal tension test
In addition to the marking prescribed in Specification A 999/A 999M, the marking shall include the length, an additional symbol “S”, if the pipe conforms to any of the Supplementary Requirements S1 to S6, the ANSI schedule number and the heat number or manufacturer’s number by which the heat can be identified. Furthermore, the marking designated in Table 6 to indicate the test method(s) shall be included. Marking may be by stenciling, stamping, or rolling. Pipe that has been weld repaired in accordance with 7.6 in ASTM A335 shall be marked “WR.”
Seamless Pipe Specifications
Standard : ASTM A335 / ASME SA335
Outside Diameter: 325-1067 mm
Wall Thickness: 9.53-140 mm
Length: On the request
|Place of Origin||China||Brand Name||BOYUE|
|Standard||ANSI, ISO, ASME, DIN, ASTM||Type||Seamless|
|ModelNumber||Alloy Steel Pipe||Thickness||SCH 5-SCH XXS|
|Packing||Depending on customer||Payment||30%TT+70% Balance|
Supply Ability:40000Pieces / per Month
Packaging & Delivery
Packaging Details:Generally plywooden case or following customer's requirement.
|Minimum Order Quantity:||1pcs|
|Price:||Depending on quantity|
|Payment Terms:||T/T or Western Union or LC|
|Supply Ability:||40000 ton per month|
|Delivery Time:||10-100 days depending on quantity|
|Packaging Details:||Depending on customer|
Why Choose Us
1. One-Stop Service,One Single Source.
2. No MOQ.
3. Best quality,competitive price
4. Fast Reply.
5. On-Time Delivery
6. Professional sales and technical team .
Q1: Are you a factory or a trade company?
A1: We are a professional manufacturer for designing and producing of Large-size products.(View Mor)
Q2: Do you make customized products or finished parts?
A2: All parts are custom made only, and in stock, we can produce based on your drawings.
Q3: Will my drawing be safe after you get it?
A3: Yes, we will not release your design to third party unless with your permission.
Q4: What is the MOQ?
A4: Small order is acceptable, but the more, the cheaper.
Q5: How about the samples?
A5: We are happy to make prototype part or sample for clients to ensure quality standard, but it’s charged according to your drawing